Installation
is easy! Just follow our three step process.
It
takes less than 10 minutes* to transform
your environment into something amazing
with vinyl lettering!
Preparation:
Your
letters come pre-spaced, made up of
3 layers:
Top Layer - Clear transfer sticking paper
Middle Layer - your letters
Bottom Layer - White or Blue, shiny backing
paper
Materials
for Installation: Squeegee or credit card
Ruler
Tape Measure
Yard Stick
Masking Tape
Once
you have chosen your desired location, clean
with mild detergent or soap and water — dry thoroughly before starting application.
STEP 1:
First,
rub the supplied squeegee tool over your lettering
to ensure it is sticking
firmly to the transfer paper.
DO
NOTuse water on your
vinyl art during
this step.
Choose
your desired location, and place the lettering on
the wall exactly the way it comes. Use pieces of masking
tape as shown to hold it into place. Adjust straightness
of decal as needed.
STEP
2:
Cut
apart large lettering between words (as shown) to
make installation easier.
Remove
backing paper from lettering. Using the supplied
tool, rub
over the lettering to securely adhere it to your
wall.
Work
slowly from the top down. Take your time with this
step to avoid bubbles or wrinkles in your artwork.
If
you get a bubble, gently rub the bubble to the edge
of the letter or use a small pin to pop the bubble
and push air out.
STEP
3:
Carefully
peel off the transfer paper to reveal your lettering.
Pull at an angle and watch that your letters are
all sticking to your surface. If you notice any
letters pulling up with the transfer paper, re-rub
onto the wall.
Presto!
You're done and ready to enjoy!
*Please
note: Installation
time may vary by individual. This timeframe is an estimate
based on studies done by Right On The Walls.
If
you have never applied vinyl before, it may take you
longer. Larger lettering with a great amount of words
and/or designs can take longer to put up than shorter
or smaller designs.
Easy
Application on Glass, Mirror, Plastic or Metal:
Please
follow the application instructions included with
your product purchase.
Additional
Installation Tips:
Thoroughly
clean your wall, make sure it is free from dust or
other residue before application.
Allow
your lettering to warm to room temperature before attempting
to apply.
Allow
newly painted walls to "cure" for two weeks before
applying your vinyl wall lettering.
If
your lettering gets wet, allow it to completely dry
before applying to an interior wall.
If
you are having trouble with the letters sticking to
the clear sticky paper ... try rubbing thoroughly on
the edge of each letter.
Always
start with a corner of the clear sticky application paper
and pull slightly sideways at an angle. If a letter is
not sticking to the clear tape, just lay the clear tape
back down over that letter only and rub the edge. You'll
notice that once the edge of the letter sticks the whole
letter should pull up easily.
You
may give
the letter edge a little help with a toothpick or small
pointed object.
Do
not
lay your clear application tape back down after you
pull it up, just keep going until you get the whole
way across, you will end up with just the clear tape
and the letters sticking to it. Apply that to the
wall.
You
may choose to cut your lettering apart and apply in
smaller sections if you wish. Just cut a square around
each section. You can even cut apart each letter if
you want to get creative in your application.
**
Will not stick to 'Candlelight' finish by Ralph Lauren.
**
Not Recommended for use with with High Gloss Painted
surfaces.
**
Knock Down Textured Walls may experience some difficulty
with edges.
Easy
Removal:
To
remove your lettering, grab the corner of each letter
with your fingernail, toothpick or a pair of tweezers.
Pull off of the wall at a slight angel. If your lettering
has been on your wall for a length of time, you may
wish to warm up the removable adhesive with a hair
dryer to speed up removal.